Taizhou Jinhao Dingyi Mould & Plastics Co., Ltd.
Set Homepage | Favorite
0576-84220820
Specialzied in compression mould and injection mould!

Basic Knowledge of Injection Molding Process

Issuing time:2020-04-03 00:00

The injection molding is the most important step to get the finished part after the mold complete; the precondition is verified injection mold, proper dried up resin, proper injection press, and experienced process engineer; simply ,Injection molding is a process of   Injection molding machine press the melted plastic into the mold and get the desired shape of plastic part after cooling and ejection up, comparing with other processing method, injection molding has advantage of efficient, productivity, it has strictly requirement for mold construction and injection press , so it is mainly for high-volume production of injection molded parts.

Injection molding machine commonly used plunger cylinder / screw cylinder. Injection molding process: Dry up the resin to required tempture within 2~4 hours, feed the plastic raw material from the hopper into the barrel, the plunger start to rotating, the plastic raw material is pushed into a heating barrel and then through the bypass shuttle, the molten plastic through the nozzle into the mold cavity, then water or oil run through the designed cooling system to cool down the mold to get a plastic article. Injection molded parts from the mold cavity is typically required for proper treatment to remove the stress generated during molding process to have good dimensional stability and performance.

There are a lot of products produced by injection molding, most of the articles we frequently use in our office or our home, industrial application, automotive, medication, etc. it contributes a lots to production efficiency and makes low cost production is realistic.

Understanding plastic injection molding process

Plastic injection molding processes consist of four main stages: filling, packing, cooling and ejection. The four stages determine the quality of the injection molded parts, and the four stages are a complete and continuous process.

Filling stage

Filling the melt flow into mold cavities is the first step in the process, the mold cavities would befilled about 95% in this stage. Generally, the shorter filling time, the higher the molding efficiency, but in practice, the injection molding time or speed is influenced by many other factors.

the viscosity of the material flow

injection pressure

injection speed (the faster the reaction the greater)

runner, gate friction loss

venting

mold structure

Mold temperature

Packing&Holding Stage

The Packing&Holding pressure is continuously applied in packing stage, the melt compacted to increase the density of the plastic (densification) to compensate for the plastic shrinkage behavior. In the packing process, pressure in the mold cavity is high because its almost full filled. Injection molding machine screw are still moving forward slightly, plastic flow rate becomes very slow, in the packing stage, plastic mold wall is cooled down and solidified until the gate is closed.

Holding pressure and speed is usually 50% to 65% of the maximum pressure and speed of filling, which means holding pressure is 0.6 ~ 0.8 MPa lower than the injection pressure.

Cooling stage

The design of the cooling system of a injection mold is very important. Because the molded plastic article to need to be cooled and solidified to avoid deformation or damage. The cooling time of the takes about 80% of injection molding cycle, so a well-designed cooling system can shorten the cycle time and improve the productivity magnificently. Poor designed cooling system will increase cycle time, increase costs; uneven cooling will cause distortion of molded parts; which will cause the failure of total project.

Ejection Stage

The last process of plastic injection molding is releasing the parts from core side, its also called demolding. Even the plastic parts have been cooled down and solidified during cooling stage, but you still need to be careful for the way of ejection. Unproper way will deform the plastic molded parts or even cause damage. There are some common methods of releasing, injector pins, stripper plate, gas assistance ejection, or take out by manual for a   rubber part, which way to go depends on the molded plastic parts structure. Ejector layout should be uniform to achieve stable releasing. Preferable location of ejector is where there is maximum strength and largest release resistance on the part. The stripper is generally used for round or deep cavity thin-walled containers or transparent products with no ejector mark allowed.

Online contact
 Work Time
Mon to Sat :8:00-17:00
 Contact Details
Tel:0576-84220820
QQ:2724736464
Email:dymould@aliyun.com
Fax:0576-81103280
Add:No.68 Lianping Road, Shi Guiao Industrial Zone, Huangyan District, Taizhou City, Zhejiang Province 3
Online map
Tel: 0576-84220820         
Email: dymould@aliyun.com
Address: No.68 Lianping Road, Shi Guiao Industrial
Zone, Huangyan District, Taizhou ,Zhejiang,China
Login
Login
Login by:
leave a message
back to the top